Grab Yours Today – Buy Now On Amazon!
Your Sales Price $78.99 - $63.99
Product Description
FC Specifications:
MCU: STM32F405RGT6, 168MHz , 1MB Flash
IMU: ICM42688-P
Baro: DPS310
OSD: AT7456E
Blackbox: MicroSD card slot
6x UARTs, 1x Softserial_Tx option(INAV)
10x PWM outputs
2x I2C
3x ADC (VBAT, Current, RSSI)
Built in inverter for SBUS input
USB Type-C(USB2.0)
FC Firmware
ArduPilot: MatekF405-Wing (ArduPlane 4.4 or newer)
INAV: MATEKF405SE (INAV 6.0 or newer)
PDB
Input voltage range: 9~30V (3~6S LiPo) w/TVS protection
Current Senor: 220A, 3.3V ADC (INAV scale 150, ArduPilot 66.7A/V)
Sense resistor: 100A continuous, 220A peak
Battery Voltage divider 1K:10K (Scale 1100 in INAV, BATT_VOLT_MULT 11.0 in ArduPilot)
BEC 5V output
Designed for Flight controller, Receiver, OSD, Camera, Buzzer, 2812 LED_Strip, Buzzer, GPS module, AirSpeed
Continuous current: 2 Amps
BEC 9V /12V output
Designed for Video Transmitter, Camera, Gimbal ect.
Continuous current: 2 Amps
12V option with Jumper pad
for stable 9V/12V output, input voltage should > output voltage +1V
BEC Vx output
Designed for Servos
Voltage adjustable, 5V Default, 6V or 7.2V options
Continuous current: 5 Amps, 6A Peak
for stable Vx output, input voltage should > Vx voltage +1V
BEC 3.3V output
Designed for external 3.3V peripherals
Linear Regulator
Continuous current: 200mA
Physical
Mounting: 30.5 x 30.5mm, Φ4mm with Grommets Φ3mm
Dimensions: 54 x 36 x 13 mm
Weight: 25g
Including
1x F405-Wing-V2
1x 20cm JST-GH-4P to JST-GH-4P cable for I2C port
Dupont 2.54 pins (Board is shipped unsoldered)
INAV firmware “MATEKF405SE” must be 6.0.0 or newer version.
Current sensor scale 150
5x Vx2 pads on S5~S9 rails are dead pins, If powering servos of S5~S9 rails with the built-in Vx BEC, bridge Vx2 to Vx pad with a drop of tin. If powering servos of S5~S9 rails with an external BEC, keep the gap open, you may connect external BEC to any pair of Vx2/G.
Softserial_tx1 is enabled on Tx2 pad by default for Frsky SmartPort telemetry. If using CRSF protocol receiver(TBS, ELRS etc), CPU based serial port(softserial) should be disable in INAV configurator.
GPS / DJI OSD and other digital video systems / CRSF protocol receiver can work with anyyyyyyy spare UART_TX & RX.
Airspeed sensor MS4525 works on I2C2 bus only.
ArduPlane firmware “MatekF405-WING” must be 4.4.0 or newer version.
BATT_AMP_PERVLT 66.7
Use 5V active buzzer on “Buz-” and 5V pads, Tone alarm is not supported.
5x Vx2 pads on S5~S9 rails are dead pins, If powering servos of S5~S9 rails with the built-in Vx BEC, bridge Vx2 to Vx pad with a drop of tin. If powering servos of S5~S9 rails with an external BEC, keep the gap open, you may connect external BEC to any pair of Vx2/G.
non-inverted (hacked) S.Port signal is required for FPort or Smartport telemetry.
If sending highspeed serial data (eg. 921600 baud) to the board, use USART1(Serial1) .
Add to Cart
Add to Cart
Add to Cart
Customer Reviews
—
4.8 out of 5 stars
24
4.6 out of 5 stars
7
4.3 out of 5 stars
54
4.0 out of 5 stars
8
Price
—
—
$84.99$84.99
$54.99$54.99
$118.99$118.99
Matek
✓
✓
✓
✓
✓
Updated version: Matek F405-WING V2 Flight Controller ,it is designed specially for fixed wing.
USB:Type-C; Baro:DPS310; Current sensor:100A continuous, 220A Peak; Current scale: INAV 150 ArduPilot BATT_AMP_PERVLT= 66.7.
INAV:MatekF405SE, 6.0 or newer;ArduPilot:MatekF405-Wing, 4.4 or newer.
MCU: STM32F405RGT6, 168MHz , 1MB Flash; IMU: ICM42688-P; Blackbox: MicroSD card slot.
6x UARTs; 2x I2C; 3x ADC; 1x Softserial_Tx option(INAV); 10x PWM outputs.
Price effective as of Nov 18, 2024 09:52:02 UTC
As an Amazon Associate Dealors may receive a
commission for purchases made through these links.
